> For the complete documentation index, see [llms.txt](https://enercalc.com/docs/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://enercalc.com/docs/sel-user-manual/calculation-modules/earth-retention/sw-segmental-walls/block-geogrid-data-tab-for-ge-2/block-geogrid-data-tab-for-ge.md).

# Block & Geogrid Data Tab (for Geogrid Reinforced Walls)

How to define block and geogrid data for geogrid-reinforced segmental retaining walls.

![](https://3283832020-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FiBJmBoewuy4ZcBC7RF3m%2Fuploads%2Fgit-blob-f788990a8a0ae377b6539e48a8e354f5887b001e%2FClip36.jpg?alt=media)

**Segmental Type**: Select either Gravity or Geogrid.

**Select Block:** From the drop down menu select the vendor and block you want to use. Selecting a block will insert its values into the criteria below.

**Block depth, in**: This will be automatically input based upon block selection.

**Block height, in**: This will be automatically input based upon block selection.

**Wall weight, psf**: This will be automatically input. Note that the full block depth is assumed to be in-filled and an average density of 120 pcf is used. Note that block weight is in units of psf. Think of looking at an elevation of a constructed wall. It is the weight of one square foot of finished wall. It is calculated by knowing the weight of the solid portion of the block and assuming that any hollow portions are filled with material that weighs 120 pcf.

**Offset per block, in**: Select this value from the drop down menu – it is vendor-dependent.

**Batter, degrees**: This angle will be computed and displayed based upon offset and block height entered.

**Total No of Block Courses:** Enter the number of block courses.

**Retained Height**: The retained height is automatically calculated and reported.

**Blocks in Layer 1**: Enter the number of courses below the first layer of geogrid.

**Blocks per Layer**: Enter the typical number of courses between layers of geogrid.

**Min Blocks above top Layer**: Enter the minimum number of courses above the top layer of geogrid.

**Base Width:** Enter the full base width including wall depth. (usually 60% - 70% of retained height).

**Select Geogrid:** From the drop down menu select the geogrid vendor and the specific geogrid. Design parameters will be displayed below.

**Ci factor**: Select the coefficient of interaction for pullout (usually 0.70 – 0.90). Note: The program will not permit a layer of geogrid to be placed under the first course, so the value of Cds, coefficient of direct sliding is hard coded to 1.0 for external sliding checks.

**LTDS, lbs/ft**: Long Term Design Strength will be automatically inserted based upon the vendor/geogrid selection.

**RF\*\*\*\*CR**: Creep Reduction Factor will be automatically inserted based upon the vendor/geogrid selection.

**LTDSseismic, lbs/ft**: Long Term Design Strength for seismic loading will be automatically calculated as LTDS / RFCR.

**C\*\*\*\*DS**: Select the coefficient of direct sliding. Reference NCMA 3rd Edition, Section 7.5.5.

**Wall Geometry Table**:

**Block**: Displays the total number of block courses.

**Layer**: Displays the geogrid layer numbers in ascending order from bottom.

**Height**: Displays block and layer heights in ft-inches and decimals.

**Show Block Courses / Show Grid Layers**: Toggles between the display of block courses or grid layers.


---

# Agent Instructions
This documentation is published with GitBook. GitBook is the documentation platform designed so that both humans and AI agents can read, navigate, and reason over technical content effectively. Learn more at gitbook.com.

## Querying This Documentation
If you need additional information that is not directly available in this page, you can query the documentation by asking a question.

Perform an HTTP GET request on the following URL with the `ask` and `goal` query parameters:

```
GET https://enercalc.com/docs/sel-user-manual/calculation-modules/earth-retention/sw-segmental-walls/block-geogrid-data-tab-for-ge-2/block-geogrid-data-tab-for-ge.md?ask=<question>&goal=<user_goal>
```

`ask` is the immediate question: it should be specific, self-contained, and written in natural language.
`goal` is what the user is ultimately trying to achieve, the reason they need the answer. Sharing it helps GitBook give you a better, more relevant answer. A goal is most helpful when it describes the outcome the user wants rather than restating the question. For example, with `ask=how do I create an API token`, a goal like `automate deployments from our CI pipeline` lets GitBook tailor the answer to that use case.

The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.
