> For the complete documentation index, see [llms.txt](https://enercalc.com/docs/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://enercalc.com/docs/sel-user-manual/calculation-modules/earth-retention/cantilevered-and-restrained-re/st-stem-tab/st-tapered-stem.md).

# Stem Tab for Tapered Stem Retaining Wall

How to design the tapered stem of a cantilevered retaining wall for moment, shear, and rebar embedment.

Tapered Stem Retaining Walls are cantilevered retaining walls where the soil face is battered to achieve a variable thickness from the base of the stem to the top of the stem.

When a Tapered Stem Retaining Wall is defined, the Stem tab will appear as shown below:

<figure><img src="https://3283832020-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FiBJmBoewuy4ZcBC7RF3m%2Fuploads%2Fgit-blob-47aef8aee014ba01c3f40aec1ebdc254f21571ce%2FTRW%20-%20Stem%20Tab.png?alt=media" alt="Stem tab for a tapered stem retaining wall, showing material, thickness, stem design, and shear inputs."><figcaption><p>Stem tab for a tapered stem retaining wall</p></figcaption></figure>

{% hint style="info" %}
Note: Taper can only apply to the inside face (the face against the soil).
{% endhint %}

**Material**: The Material will automatically be defined as Concrete, since masonry cannot be tapered.

**Thickness:** Top and Base: Enter the stem thickness at the top and at the bottom.

**Concrete Density**: Use the spinners to set the unit weight of the concrete.

**f’c and Fy**: Enter concrete strength and rebar yield stress.

**Rebar Cover**: Select the rebar clear cover to consider in the design.

**Stem Design**: Stem design will automatically be performed at the bottom of the stem (interface with the footing). In addition, you can specify two additional heights above the base to check moments and shears. These are identified as "@ Height #2" and "@ Height #1", where the latter is the lower height.

**Ht. Above Footing**: Specify two heights above the top of footing elevation where a stem design should be performed (such as where it would be desirable to change the rebar pattern or size for economy). Height #2 is highest and Height at Stem Base will be fixed at 0.00. The #1 height should be located at a distance above the top of the footing that is at least equal to the lap splice length for the dowels.

**Rebar Depth "d"**: This will be computed based upon the heights you have chosen, the specified wall taper, and the specified Rebar Cover. The program automatically uses the specified clear cover and one-half of a bar diameter when determining "d".

**Rebar Size**: Use the drop-down list box to select the desired rebar size.

**Rebar Spacing**: Use the spinners to set the desired rebar spacing. (The maximum permissible spacing is 18 inches, which is in accordance with ACI.)

**Mu**: These are factored moments at the heights you have selected. These will be based on the load factors that you specify on the Load Factors tab. Compare these values with Design Moment as described below, to verify adequacy of your design at the selected height location.

**φMn**: This is the design moment strength, which will be based upon the bar sizes and spacings you established, along with wall geometry, concrete strength, etc.

**As,min <= As <= As,max**: This reports the steel-ratio check for each stem section. It displays "As < As,min", "OK", or "As > As,max" depending on whether the provided steel falls within the code minimum and maximum limits.

**Moment Capacity**: This indicates whether each stem design is adequate for moment at the specified height. If there's a problem, it displays a descriptive message such as "Mu > Phi \* Mn".

**Rebar Lap Req'd**: This is the lap splice length required based on the bar size used at the specified Design Height. It is the development length of the bar multiplied by 1.3 (assuming a Class B splice) and without adjustment for stress level.

**Rebar Hooked Embedment Length**: This is the hooked development length that is required into the concrete footing for the bar size specified at the stem base. For more information, see [Summary Section of Stem Tab - Hooked Embedment of Rebar in Concrete](https://enercalc.com/docs/sel-user-manual/calculation-modules/earth-retention/cantilevered-and-restrained-re/st-stem-tab/st-cantilevered-wall/rt-stress-ratio.md#HookedEmbedmentofRebarinConcrete).

**Shear at Section**: This is the total factored shear at the indicated height.

**Vu**: Factored shear stress at designated height computed by Shear at Section / (12 \* "d").

**φVn**: For concrete stems designed per ACI 318-14 and earlier, or ACI 318-25 and later with *"Use simplified Vc equation (Section 13.3.6.1.1)"* enabled, the nominal shear strength is calculated as follows:

φ vn = φ \* 2 \* λ \* √(f'c), where φ = 0.75.

For concrete stems designed per ACI 318-19, or ACI 318-25 and later with *"Use simplified Vc equation (Section 13.3.6.1.1)"* enabled, the nominal shear strength follows the one-way shear provisions of §22.5 and Table 22.5.5.1 (referenced by §13.3.6.1 and §7.5.3.1):

φ vn = φ \* 8 \* λs \* λ \* (ρw)1/3 \* √(f'c), where φ = 0.75.

{% hint style="info" %}
Note: The one-way shear capacity assumes no transverse reinforcement in the stem. Therefore, Av < Av,min, and equations (a) and (b) from Table 22.5.5.1 are not applicable.
{% endhint %}

This value is also subject to additional limits per §22.5.5.1.1:

Lower bound: φ \* λ \* √(f'c) (ACI 318-25 and later only)

Upper bound: φ \* 5 \* λ \* √(f'c)

**Reduce hooked embedment by As req'd/As provided**: When this option is selected, the program reduces the calculated hooked embedment depth by applying the ratio of required steel area to provided steel area. This setting is unavailable for ACI 318-19 and later editions as Section 25.4.10 does not permit reducing hooked development length by the ratio of (As,required / As,provided).

**Use simplified Vc equation (Section 13.3.6.1.1):** For cantilever retaining walls, ACI 318-25 Section 13.3.6.1.1 allows a simplified shear equation (Vc = 2 λ √(f'c) bw d) as an alternative to the one-way shear provisions in Section 22.5.5.1. Enabling this option usually gives a higher shear capacity. For walls with higher reinforcement ratios, Section 22.5.5.1 can still produce larger values, which happens when this option is disabled.

**Hooked Embedment Modifiers**: These are the various hooked embedment modifiers used in the hooked development length calculations. For more information, see ACI 318 Table 25.4.3.2 and [Summary Section of Stem Tab - Hooked Embedment of Rebar in Concrete](https://enercalc.com/docs/sel-user-manual/calculation-modules/earth-retention/cantilevered-and-restrained-re/st-stem-tab/st-cantilevered-wall/rt-stress-ratio.md#HookedEmbedmentofRebarinConcrete).


---

# Agent Instructions
This documentation is published with GitBook. GitBook is the documentation platform designed so that both humans and AI agents can read, navigate, and reason over technical content effectively. Learn more at gitbook.com.

## Querying This Documentation
If you need additional information that is not directly available in this page, you can query the documentation by asking a question.

Perform an HTTP GET request on the following URL with the `ask` and `goal` query parameters:

```
GET https://enercalc.com/docs/sel-user-manual/calculation-modules/earth-retention/cantilevered-and-restrained-re/st-stem-tab/st-tapered-stem.md?ask=<question>&goal=<user_goal>
```

`ask` is the immediate question: it should be specific, self-contained, and written in natural language.
`goal` is what the user is ultimately trying to achieve, the reason they need the answer. Sharing it helps GitBook give you a better, more relevant answer. A goal is most helpful when it describes the outcome the user wants rather than restating the question. For example, with `ask=how do I create an API token`, a goal like `automate deployments from our CI pipeline` lets GitBook tailor the answer to that use case.

The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.
