> For the complete documentation index, see [llms.txt](https://enercalc.com/docs/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://enercalc.com/docs/sel-user-manual/calculation-modules/earth-retention/cantilevered-and-restrained-re/rt-results-tab/rt-summary.md).

# Summary

How to review footing soil bearing, stability ratios, and factored footing design results for retaining walls.

This screen summarizes the footing/soil bearing results obtained from previous screens, including a message whether the resultant is within or outside the middle third of the footing.

![](https://3283832020-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FiBJmBoewuy4ZcBC7RF3m%2Fuploads%2Fgit-blob-eb0839a0784b9fe79a944ecace973ce4109d9c7c%2FEarth%20Retention%20-%20Results%20Summary.png?alt=media)

This is not an input screen. It's strictly for your review, and it does not appear if a pier is specified.

**Stability Ratios**: These are displayed for both overturning and sliding.

**Soil Loading Results**

**Soil Pressure @ Toe and Heel**: This is the resulting soil pressure for both the toe and heel based on service loads. If the eccentricity is outside the middle third, the heel pressure will show 0.00, and the program will calculate the toe pressure assuming no tension at the heel.

**Allowable Soil Pressure**: This is for reference as entered on the General tab.

**Total Bearing Load**: This is the sum of all vertical forces.

**Resultant Eccentricity**: Distance from center of footing to the resultant of the soil pressure distribution.

**Eccentricity Within/Outside Middle Third**: If the eccentricity is greater than one-sixth the footing width, the resultant is outside the middle third. (If outside the middle third, the program computes the toe soil pressure assuming no tension at the heel.)

**Footing Results**

**ACI Factored Soil Pressure @ Toe and Heel**: ACI load factors are applied to all loads to determine total vertical load for soil pressure used in calculating footing moments and shears. This load is then applied at the same eccentricity calculated for service load soil pressures to yield the factored soil pressures for footing design using LRFD design principles.

Note that since factored vertical loads are applied at the non-factored resultant eccentricity, a true 1.6 load factor applied to lateral earth pressure is not used for footing design. ACI load factors are intended to give conservative results for design. Calculation of a factored load eccentricity would give soil pressure diagrams that would not always represent the actual soil pressure distribution under the footing, and yield unreasonable results. Factored lateral earth pressure, however, is always used for concrete stem design.

**M\*\*\*\*u** **Design @ Toe/Heel**: These are the factored moments at face of stem for toe and heel moments. Since neither can be greater than the stem base moment (factored if concrete stem), the latter may govern. These moments will be reduced if you choose to neglect the upward soil pressure on the Footing tab. A message will indicate which controls.

The program assumes that the tension face and associated reinforcement will be at the bottom face of the toe and the top face of the heel. If the loading does not meet these conditions, the Mu value will be displayed in red, and a warning message will indicate: "Hand Calc Required - Value Negative." These conditions are beyond the scope of this module and require a separate hand calculation to verify adequacy.

**Shear @ Toe and Heel**: These items report the factored shear stress from the one-way action in the footing. The toe shear stress is calculated at a distance "d" (footing thickness - rebar cover) from the face of the bottom stem segment. (If "d" is greater than the projecting toe length, then the one-way toe shear is reported as zero.) The heel shear stress is calculated at the face of the stem.

**Allowable Footing Shear**: **For footings designed per ACI 318-14 and earlier, and ACI 318-25 and later:**

The nominal shear strength follows the one-way shear provisions of ACI 318-14 §22.5.5.1 / ACI 318-25 §13.2.6.2:

φ vn = φ \* 2 \* λ \* √(f'c), where φ = 0.75.

**For footings designed per ACI 318-19:**

The nominal shear strength follows the one-way shear provisions of §22.5 and Table 22.5.5.1 (referenced by §7.5.3.1):

φ vn = φ \* 8 \* λs \* λ \* (ρw)1/3 \* √(f'c), where φ = 0.75.

{% hint style="info" %}
Note: The one-way shear capacity assumes no transverse reinforcement in the footing. Therefore, Av < Av,min, and equations (a) and (b) from Table 22.5.5.1 are not applicable. It is also acceptable to neglect the size effect factor (λs) for one-way shallow foundations per §13.2.6.3, so λs is taken as 1.0.
{% endhint %}

This value is also subject to additional limits per §22.5.5.1.1:

Lower bound: φ \* λ \* √(f'c)

Upper bound: φ \* 5 \* λ \* √(f'c)


---

# Agent Instructions
This documentation is published with GitBook. GitBook is the documentation platform designed so that both humans and AI agents can read, navigate, and reason over technical content effectively. Learn more at gitbook.com.

## Querying This Documentation
If you need additional information that is not directly available in this page, you can query the documentation by asking a question.

Perform an HTTP GET request on the following URL with the `ask` and `goal` query parameters:

```
GET https://enercalc.com/docs/sel-user-manual/calculation-modules/earth-retention/cantilevered-and-restrained-re/rt-results-tab/rt-summary.md?ask=<question>&goal=<user_goal>
```

`ask` is the immediate question: it should be specific, self-contained, and written in natural language.
`goal` is what the user is ultimately trying to achieve, the reason they need the answer. Sharing it helps GitBook give you a better, more relevant answer. A goal is most helpful when it describes the outcome the user wants rather than restating the question. For example, with `ask=how do I create an API token`, a goal like `automate deployments from our CI pipeline` lets GitBook tailor the answer to that use case.

The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.
