For the complete documentation index, see llms.txt. This page is also available as Markdown.

Worked Example 2

Compute the forces on the shear walls of the one-story, rigid diaphragm shear wall building. See Figure 9, and Example Problem 1 for additional information.

Figure 9: Example Problem #2 - Plan View

Wall assembly A is at ϕ=53.13∘\phi = 53.13^{\circ} to the z axis, see Figure 10. The moments of inertia, neglecting small quantities, are calculated as follows:

I2=812(25)3(112)=868 ft4I_2 = \frac{8}{12} (25)^3 \left( \frac{1}{12} \right) = 868\ \text{ft}^4

I1=25(812)3(112)=0.62 ft4I_1 = 25 \left( \frac{8}{12} \right)^3 \left( \frac{1}{12} \right) = 0.62\ \text{ft}^4

Recall from Figure 5, with 2α=180−2(53.31)=73.382\alpha = 180 - 2(53.31) = 73.38

R=12(868−0.62)=433.69R = \frac{1}{2}(868 - 0.62) = 433.69

C=0.62+433.69=434.31C = 0.62 + 433.69 = 434.31

Izz=434.31+433.69cos⁡(73.38)=558.35I_{zz} = 434.31 + 433.69 \cos(73.38) = 558.35

Iyy=434.31−433.69cos⁡(73.38)=310.26I_{yy} = 434.31 - 433.69 \cos(73.38) = 310.26

Iyz=433.69sin⁡(73.38)=415.57I_{yz} = 433.69 \sin(73.38) = 415.57

The cross-sectional area

A=812(25)=16.67 ft2A = \frac{8}{12}(25) = 16.67\ \text{ft}^2

The stiffness coefficients for wall assembly A can now be computed from the flexibility matrix as per example problem 1. Recall Equation 4 and Figure 10:

ΔUy1=Vy1E[(12)33(868)+2.64(12)16.67]=2.56Vysin⁡ϕE\Delta U_{y1} = \frac{V_{y1}}{E} \left[ \frac{(12)^3}{3(868)} + \frac{2.64(12)}{16.67} \right] = \frac{2.56V_y \sin\phi}{E}

ΔUy2=Vy2E[(12)33(0.62)+2.64(12)16.67]=931Vycos⁡ϕE\Delta U_{y2} = \frac{V_{y2}}{E} \left[ \frac{(12)^3}{3(0.62)} + \frac{2.64(12)}{16.67} \right] = \frac{931V_y \cos\phi}{E}

Figure 10: Example Problem #2 - Wall Element A w/ Unit Load Vy

Now,

Uzy1=ΔUy1cos⁡ϕ=2.56Vysin⁡ϕcos⁡ϕE=1.228VyEU_{zy1} = \Delta U_{y1} \cos\phi = \frac{2.56V_y \sin\phi \cos\phi}{E} = \frac{1.228V_y}{E}

Uyy1=ΔUy1sin⁡ϕ=2.56Vysin⁡ϕsin⁡ϕE=1.638VyEU_{yy1} = \Delta U_{y1} \sin\phi = \frac{2.56V_y \sin\phi \sin\phi}{E} = \frac{1.638V_y}{E}

Uzy2=ΔUy2sin⁡ϕ=931Vycos⁡ϕsin⁡ϕE=447VyEU_{zy2} = \Delta U_{y2} \sin\phi = \frac{931V_y \cos\phi \sin\phi}{E} = \frac{447V_y}{E}

Uyy2=ΔUy2cos⁡ϕ=931Vycos⁡ϕcos⁡ϕE=335VyEU_{yy2} = \Delta U_{y2} \cos\phi = \frac{931V_y \cos\phi \cos\phi}{E} = \frac{335V_y}{E}

Next,

Ayy=Uyy1+Uyy2=337VyEA_{yy} = U_{yy1} + U_{yy2} = \frac{337V_y}{E}

Azy=Uzy1−Uzy2=−446VyEA_{zy} = U_{zy1} - U_{zy2} = \frac{-446V_y}{E}

Recall Equation 4 and Figure 11:

ΔUz1=Vz1E[(12)33(868)+2.64(12)16.67]=2.56Vzcos⁡ϕE\Delta U_{z1} = \frac{V_{z1}}{E} \left[ \frac{(12)^3}{3(868)} + \frac{2.64(12)}{16.67} \right] = \frac{2.56V_z \cos\phi}{E}

ΔUz2=Vz2[(12)33(0.62)+2.64(12)16.67]=931Vzsin⁡ϕE\Delta U_{z2} = V_{z2} \left[ \frac{(12)^3}{3(0.62)} + \frac{2.64(12)}{16.67} \right] = \frac{931V_z \sin\phi}{E}

Figure 11: Example Problem #2 - Wall Element A w/ Unit Load Vx

Now,

Uyz1=ΔUz1sin⁡ϕ=2.56Vzcos⁡ϕsin⁡ϕE=1.228VzEU_{yz1} = \Delta U_{z1} \sin\phi = \frac{2.56V_z \cos\phi \sin\phi}{E} = \frac{1.228V_z}{E}

Uzz1=ΔUz1cos⁡ϕ=2.56Vzcos⁡ϕcos⁡ϕE=0.921VzEU_{zz1} = \Delta U_{z1} \cos\phi = \frac{2.56V_z \cos\phi \cos\phi}{E} = \frac{0.921V_z}{E}

Uyz2=ΔUz2cos⁡ϕ=931Vzsin⁡ϕcos⁡ϕE=447VzEU_{yz2} = \Delta U_{z2} \cos\phi = \frac{931V_z \sin\phi \cos\phi}{E} = \frac{447V_z}{E}

Uzz2=ΔUz2sin⁡ϕ=931Vzsin⁡ϕsin⁡ϕE=596VzEU_{zz2} = \Delta U_{z2} \sin\phi = \frac{931V_z \sin\phi \sin\phi}{E} = \frac{596V_z}{E}

Next,

Ayz=Uyz1−Uyz2=−446VzEA_{yz} = U_{yz1} - U_{yz2} = \frac{-446V_z}{E}

Azz=Uzz1+Uzz2=597VzEA_{zz} = U_{zz1} + U_{zz2} = \frac{597V_z}{E}

The flexibility matrix equation is now,

[UyUz]=1E[337−446−446597][VyVz]\begin{bmatrix} U_y \\ U_z \end{bmatrix} = \frac{1}{E} \begin{bmatrix} 337 & -446 \\ -446 & 597 \end{bmatrix} \begin{bmatrix} V_y \\ V_z \end{bmatrix}

The stiffness matrix equation is generated by inverting the flexibility matrix; thus,

[VyVz]=E⋅[0.2630.1960.1960.148][UyUz]\begin{bmatrix} V_y \\ V_z \end{bmatrix} = E \cdot \begin{bmatrix} 0.263 & 0.196 \\ 0.196 & 0.148 \end{bmatrix} \begin{bmatrix} U_y \\ U_z \end{bmatrix}

Where

Kyy=0.263E,Kyz=0.196E,Kzz=0.148E,Kzy=0.196EK_{yy} = 0.263E,\quad K_{yz} = 0.196E,\quad K_{zz} = 0.148E,\quad K_{zy} = 0.196E

The stiffness coefficient for wall B and C are computed as in example problem 1.

For wall B, Kzz=0.289K_{zz} = 0.289 and Kyy=Kyz=0K_{yy} = K_{yz} = 0.

For wall C, Kyy=0.289K_{yy} = 0.289 and Kzz=Kyz=0K_{zz} = K_{yz} = 0.

The location of the coordinate axis system can now be computed. See Figure 12:

Figure 12: Example Problem #2 - Center of Rigidity and Wall Loads

Recall Equation 31 and 32, divide through by E,

zˉ(0.289+0.263)−yˉ(0.196)=85(0.289)+7.5(0.263)−30(0.196)\bar{z} (0.289 + 0.263) - \bar{y} (0.196) = 85 (0.289) + 7.5 (0.263) - 30 (0.196)

zˉ(0.196)−yˉ(0.289+0.148)=7.5(0.196)−30(0.148)\bar{z} (0.196) - \bar{y} (0.289 + 0.148) = 7.5 (0.196) - 30 (0.148)

Combine terms and multiply by opposite yˉ\bar{y} coefficients,

zˉ(0.552)(0.437)−yˉ(0.196)(0.437)=20.657(0.437)\bar{z} (0.552) (0.437) - \bar{y} (0.196) (0.437) = 20.657 (0.437)

zˉ(0.196)(−0.196)−yˉ(0.437)(−0.196)=−2.97(−0.196)\bar{z} (0.196) (-0.196) - \bar{y} (0.437) (-0.196) = -2.97 (-0.196)

Next,

zˉ(0.203)=9.609\bar{z} (0.203) = 9.609

Thus,

zˉ=47.34 ft2\boxed{ \bar{z} = 47.34\ \text{ft}^2 }

Now,

47.34(0.552)−yˉ(0.196)=20.65747.34 (0.552) - \bar{y} (0.196) = 20.657

Therefore,

yˉ=27.93 ft2\boxed{ \bar{y} = 27.93\ \text{ft}^2 }

The location of the coordinate axis system, the center of rigidity (CR), is now known. See Figure 12. The following loads are applied through the center of mass (CM).

Py=10 kips,Pz=10 kipsP_y = 10\ \text{kips}, \quad P_z = 10\ \text{kips}

The resulting torsional movement (Tp=zPy+yPzT_p = zP_y + yP_z)

Tp=4.84(10)−7.93(10)=−30.9 ft-kipsT_p = 4.84(10) - 7.93(10) = -30.9\ \text{ft-kips}

The torsional rigidities of the individual elements about their own shear centers (JJ) is zero. The sum of the torsional resistance of the entire

system (JpJ_p) is as follows (recall Equation 26).

Jp=(37.66)2(0.289)E+(39.89)2(0.263)E+(27.93)2(0.289)E+(2.07)2(0.148)E−2(2.07)(39.84)(0.196)E=1,021.52EJ_p = (37.66)^2 (0.289)E + (39.89)^2 (0.263)E + (27.93)^2 (0.289)E + (2.07)^2 (0.148)E - 2(2.07)(39.84)(0.196)E = 1,021.52E

The displacement may now be computed. Recall Equation 23 and 24.

10=Δy(0.289+0.263)E+Δz(0.196)E10 = \Delta_y (0.289 + 0.263) E + \Delta_z (0.196) E

10=Δy(0.196)E+Δz(0.289+0.148)E10 = \Delta_y (0.196) E + \Delta_z (0.289 + 0.148)E

Combine terms and multiply by opposite Δz\Delta_z coefficient,

10(0.437)=Δy(0.552)(0.437)E+Δz(0.196)(0.437)E10 (0.437) = \Delta_y (0.552)(0.437) E + \Delta_z (0.196)(0.437) E

10(−0.196)=Δy(0.196)(−0.196)E+Δz(0.437)(−0.196)E10 (-0.196) = \Delta_y (0.196)(-0.196) E + \Delta_z (0.437)(-0.196) E

Thus,

2.41=Δy(0.203)E2.41 = \Delta_y (0.203) E

Therefore,

Δy=11.89E\Delta_y = \frac{11.89}{E}

Now,

10=11.89E(0.196)E+Δz(0.437)E10 = \frac{11.89}{E} (0.196) E + \Delta_z (0.437) E

Thus,

Δz=17.55E\Delta_z = \frac{17.55}{E}

Next recall Equation 25

−30.9=Δθ(1,021.52)E-30.9 = \Delta_\theta (1,021.52) E

Thus,

Δθ=−0.030E\Delta_\theta = \frac{-0.030}{E}

The forces on the walls may now be computed. See Figure 12. Recall Equation 14.

For wall A,

Fy=0.263E(11.89E)+0.196E(17.55E)+[2.07(0.196)E−(−39.84)(0.263)E](−0.030E)F_y = 0.263E \left( \frac{11.89}{E} \right) + 0.196E \left( \frac{17.55}{E} \right) + \left[ 2.07(0.196)E - (-39.84)(0.263)E \right] \left( \frac{-0.030}{E} \right)

Fy=6.24 kips\boxed{ F_y = 6.24\ \text{kips} }

Fz=0.196E(11.89E)+0.148E(17.55E)+[2.07(0.148)E−(−39.84)(0.196)E](−0.030E)F_z = 0.196E \left( \frac{11.89}{E} \right) + 0.148E \left( \frac{17.55}{E} \right) + \left[ 2.07(0.148)E - (-39.84)(0.196)E \right] \left( \frac{-0.030}{E} \right)

Fz=4.69 kips\boxed{ F_z = 4.69\ \text{kips} }

For wall B,

Fy=0 kips\boxed{ F_y = 0\ \text{kips} }

Fz=0+0.289E(17.55E)+[−27.93(0.289)E−0](−0.030E)F_z = 0 + 0.289E \left( \frac{17.55}{E} \right) + \left[ -27.93(0.289)E - 0 \right] \left( \frac{-0.030}{E} \right)

Fz=5.31 kips\boxed{ F_z = 5.31\ \text{kips} }

For wall C,

Fz=0 kips\boxed{ F_z = 0\ \text{kips} }

Fy=0.289E(11.89E)+0+[0−37.66(0.289)E](−0.030E)F_y = 0.289E \left( \frac{11.89}{E} \right) + 0 + \left[ 0 - 37.66(0.289)E \right] \left( \frac{-0.030}{E} \right)

Fy=3.76 kips\boxed{ F_y = 3.76\ \text{kips} }

Check load distribution

ΣFz=0; 10=4.69+5.31∴OK\Sigma F_z = 0; \quad \ 10 = 4.69 + 5.31 \quad \quad \therefore\text{OK}

ΣFy=0; 10=6.24+3.76∴OK\Sigma F_y = 0; \quad \ 10 = 6.24 + 3.76 \quad \quad \therefore\text{OK}

ΣTp=0; 30.9=3.76(37.66)+5.31(27.93)−6.24(39.84)−4.69(2.07)∴OK\Sigma T_p = 0; \quad \ 30.9 = 3.76 (37.66) + 5.31 (27.93) - 6.24 (39.84) - 4.69 (2.07) \quad \quad \therefore\text{OK}

Last updated

Was this helpful?