> For the complete documentation index, see [llms.txt](https://enercalc.com/docs/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://enercalc.com/docs/sel-user-manual/calculation-modules/analysis/2-d-frame-analysis/load-combinations.md).

# Load Combinations

How to define load, reaction, and deflection combinations and apply automatic member self-weight.

This data table controls how all of the loads are combined, and also enables you to have member self weight loads automatically considered in specified directions. Note that there is are three Load Combination tabs:

* ASD Load Combinations or LRFD Load Combinations (Based on your selection of Design Method on the General tab. Used for member design code checks.)
* Reaction Combinations (Always service level combinations. Used to calculate reactions.)
* Deflection Combinations (Always service level combinations. Used to calculate deflections.)

### Load Combination Set

The Select button is used to retrieve load combination sets from the built-in load combination database and place them in the list. Clicking it will display a dropdown menu listing the load combination sets currently included in the database.

![](https://3283832020-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FiBJmBoewuy4ZcBC7RF3m%2Fuploads%2Fgit-blob-1db43252b112d322d0a7a653eda68e618e2652bd%2FclipP361.gif?alt=media)

### Add (plus button)

This button adds a load combination line to the list. You can then edit the factors.

### Delete (minus button)

This button deletes the currently selected load combination from the list.

![](https://3283832020-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FiBJmBoewuy4ZcBC7RF3m%2Fuploads%2Fgit-blob-e6600959b0c75c4f114b30872bf538fc7074b893%2Fclipp360.gif?alt=media) This button allow you to edit the currently selected load combination.

Description of columns in table

### Run

This column is a Yes/No toggle to control whether that load combination is used or ignored.

![](https://3283832020-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FiBJmBoewuy4ZcBC7RF3m%2Fuploads%2Fgit-blob-4b495945da67a437f9211e64aa374f2c082a080c%2Fclip0334_was_BMP.jpg?alt=media) This button allows you to change the Run setting for all the load combinations at once using several options.

![](https://3283832020-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FiBJmBoewuy4ZcBC7RF3m%2Fuploads%2Fgit-blob-6265243b533a75c2068845aa22eb639238e1ab44%2Fclipp363.gif?alt=media)

### Load Combination

This is column represents the load combination. It consists of abbreviations for each included load type along with the associated numeric values that represent the respective load factors. You cannot directly edit this string. It is constructed automatically based on the entries you make in the following columns.

Note in the following image how the Load Combination Name is constructed from the specified values:

![](https://3283832020-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FiBJmBoewuy4ZcBC7RF3m%2Fuploads%2Fgit-blob-4b04f3775e63088c9b2ea19539ca38fb32a67c1d%2Fclipp362.gif?alt=media) Load Duration Factor (Not a load factor. Applies to wood designs only.) This value acts as a multiplier on the allowable stress for the corresponding load combination.

### Individual Load Factors

Enter the numeric value to be applied to each type of load.

### 0.2\*SDS\*Seismic Factor

When a value of Sds is specified, this column will report the additional component of vertical load that is to be included due to seismic loading.

### Member Self Weight

The controls at the bottom of the Load Combinations tabs indicate whether the program should automatically apply member self weight. Note that automatic application of self-weight can be set up differently on the three Load Combination sub-tabs, if desired. Alternatively, there is a convenience button to copy the self-weight settings from the first tab to the other two tabs, if the goal is to make them all the same.

When self-weight is non-zero, the module will calculate the weight of each member (as cross sectional area \* density \* length) and consider that weight during the analysis.

Note that the controls allow for the self-weight to be assigned to the Dead Load or the Seismic Load case, and to be assigned a direction and a percentage if desired. This makes it possible to model, say, 30% of the self-weight as an applied lateral load to be considered a Seismic Load.

![](https://3283832020-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FiBJmBoewuy4ZcBC7RF3m%2Fuploads%2Fgit-blob-1d1bfd9daa2082ae0069cb4fb9ee9377a9d205f1%2FclipP359.gif?alt=media)


---

# Agent Instructions
This documentation is published with GitBook. GitBook is the documentation platform designed so that both humans and AI agents can read, navigate, and reason over technical content effectively. Learn more at gitbook.com.

## Querying This Documentation
If you need additional information that is not directly available in this page, you can query the documentation by asking a question.

Perform an HTTP GET request on the following URL with the `ask` and `goal` query parameters:

```
GET https://enercalc.com/docs/sel-user-manual/calculation-modules/analysis/2-d-frame-analysis/load-combinations.md?ask=<question>&goal=<user_goal>
```

`ask` is the immediate question: it should be specific, self-contained, and written in natural language.
`goal` is what the user is ultimately trying to achieve, the reason they need the answer. Sharing it helps GitBook give you a better, more relevant answer. A goal is most helpful when it describes the outcome the user wants rather than restating the question. For example, with `ask=how do I create an API token`, a goal like `automate deployments from our CI pipeline` lets GitBook tailor the answer to that use case.

The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.
